Kawi2strokes.com Forum

Enthusiasts from around the world dedicated to the preservation and ritual flogging of the infamous Kawasaki 2-stroke Triples
It is currently Tue Jul 22, 2025 6:13 am

Board index » Our legendary Kawasaki Triples » Restoring your old gal, all shiny like when she was new

All times are UTC - 5 hours




Post new topic Reply to topic  Page 5 of 16
  [ 153 posts ]  Go to page Previous  1, 2, 3, 4, 5, 6, 7, 8 ... 16  Next
  Print view Previous topic | Next topic 
Author Message
Yeddy911
 Post subject: Re: 1972 Kawasaki H2 750
PostPosted: Sun Apr 04, 2021 7:56 am 
User avatar

Joined: Sun Feb 21, 2021 5:59 am
Posts: 154
Location: NY
I had a little time to work on the bike. I decided to get rid of the clicking feel up front. Installed some tapered roller bearings.


You do not have the required permissions to view the files attached to this post.

Top
 Profile  
 
Yeddy911
 Post subject: Re: 1972 Kawasaki H2 750
PostPosted: Sun Apr 04, 2021 9:53 am 
User avatar

Joined: Sun Feb 21, 2021 5:59 am
Posts: 154
Location: NY
New Seat cover and foam are in. A little pan clean up and paint soon.


You do not have the required permissions to view the files attached to this post.

Top
 Profile  
 
Yeddy911
 Post subject: Re: 1972 Kawasaki H2 750
PostPosted: Mon Apr 05, 2021 6:21 pm 
User avatar

Joined: Sun Feb 21, 2021 5:59 am
Posts: 154
Location: NY
Top of seat pan suffers the most from foam retaining moisture. Original foam was mostly a crumbly yellow substance. Pan is in pretty good shape in general.
Trim pieces are in good shape, just have to get the 6 mounting screws.


You do not have the required permissions to view the files attached to this post.

Top
 Profile  
 
Yeddy911
 Post subject: Re: 1972 Kawasaki H2 750
PostPosted: Sun Apr 11, 2021 6:54 pm 
User avatar

Joined: Sun Feb 21, 2021 5:59 am
Posts: 154
Location: NY
Working on cleaning the engine case. I made a plate to keep the grunge away from the crank and rods.
It's almost clean enough to remove the oil injection and side cover.


You do not have the required permissions to view the files attached to this post.

Top
 Profile  
 
Yeddy911
 Post subject: Re: 1972 Kawasaki H2 750
PostPosted: Sat Apr 17, 2021 9:20 am 
User avatar

Joined: Sun Feb 21, 2021 5:59 am
Posts: 154
Location: NY
H2RTuner wrote:
A Brillo pad works better than plain steel wool.

I did quite a bit of sanding, and then Brillo. Getting close.


You do not have the required permissions to view the files attached to this post.

Top
 Profile  
 
Never2Old
 Post subject: Re: 1972 Kawasaki H2 750
PostPosted: Tue Apr 20, 2021 6:15 pm 
User avatar

Joined: Tue Sep 01, 2020 5:19 am
Posts: 146
Location: canton, ct
Guys, after you get these aluminum parts looking good, is there any way to keep them shiny? Or are they just going to start oxidizing and over time?

Dave, still hunting for my H2
Top
 Profile  
 
H2RTuner
 Post subject: Re: 1972 Kawasaki H2 750
PostPosted: Tue Apr 20, 2021 7:11 pm 

Joined: Thu Jun 09, 2011 11:25 am
Posts: 3164
When I do an aluminum car distributor conversion, it comes with a complete rebuild, including glass bead blasting. This disturbs the aluminum, to the point it is uneven and the pores are open to collecting greases, dirt, oils, grime, and not easily cleaned. What I do to "dress" the blasted surface back to darned near stock finish, is to take the part to the sink, use warm water and Brillo pads, NOT steel wool, BRILLO pads, hand massaged. The pores are closed back down, the finish is good, and the grime and dirt, oils, greases are not held in the open pores.

Try it on a s crap piece of aluminum, it might be what you seek

I tried to add a picture of a Chevy distributor with the process already done to it, but I don't know if it worked. EDIT: Looks like it worked.

Attachment:
Chevrolet HEI front.JPG


You do not have the required permissions to view the files attached to this post.

Top
 Profile  
 
Yeddy911
 Post subject: Re: 1972 Kawasaki H2 750
PostPosted: Wed Apr 21, 2021 6:49 am 
User avatar

Joined: Sun Feb 21, 2021 5:59 am
Posts: 154
Location: NY
Never2Old wrote:
Guys, after you get these aluminum parts looking good, is there any way to keep them shiny? Or are they just going to start oxidizing and over time?

Dave, still hunting for my H2

I'm going to spray them with SprayMax 3680061, 2K Urethane Clear Coat.
Top
 Profile  
 
mraxl
 Post subject: Re: 1972 Kawasaki H2 750
PostPosted: Wed Apr 21, 2021 7:28 am 
Site Admin
User avatar

Joined: Tue Jun 07, 2011 6:36 am
Posts: 2718
Location: Dandridge, TN, USA
Many spray coatings will yellow with time and/or not withstand gas/oil.
Polished surfaces will remain looking good with an occasional wipe with Nevr-Dull.
http://www.nevrdull.com/

_________________
Answers are here: http://kawatriple.com/
Top
 Profile  
 
H2RTuner
 Post subject: Re: 1972 Kawasaki H2 750
PostPosted: Wed Apr 21, 2021 3:55 pm 

Joined: Thu Jun 09, 2011 11:25 am
Posts: 3164
Try the Brillo pad first, then, if you must, coat with the clear. Dale is right, most all the clear coatings eventually yellow.
Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  Page 5 of 16
  [ 153 posts ]  Go to page Previous  1, 2, 3, 4, 5, 6, 7, 8 ... 16  Next

Board index » Our legendary Kawasaki Triples » Restoring your old gal, all shiny like when she was new

All times are UTC - 5 hours


Who is online

Users browsing this forum: No registered users

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Jump to:  
Powered by phpBB® Forum Software © phpBB Group