Kawi2strokes.com Forum

Enthusiasts from around the world dedicated to the preservation and ritual flogging of the infamous Kawasaki 2-stroke Triples
It is currently Sun Jun 16, 2024 10:33 am

Board index » Our legendary Kawasaki Triples » General Chat

All times are UTC - 5 hours




Post new topic Reply to topic  Page 1 of 2
  [ 15 posts ]  Go to page 1, 2  Next
  Print view Previous topic | Next topic 
Author Message
saint barry
PostPosted: Wed Aug 27, 2014 1:45 am 

Joined: Sun Jun 12, 2011 10:56 pm
Posts: 1188
Who is selling packages of the smaller diameter chamber nuts ??? Thanks for the info !!!!!
Top
 Profile  
 
Iron
PostPosted: Wed Aug 27, 2014 6:55 am 
User avatar

Joined: Thu Jun 09, 2011 8:52 pm
Posts: 849
Location: South Louisiana
Don't know. Did you think about pulling the studs and putting allen bolts?

_________________
Iron On The Bayou.
Top
 Profile  
 
III
PostPosted: Wed Aug 27, 2014 7:00 am 
User avatar

Joined: Wed Jun 08, 2011 10:41 pm
Posts: 3489
Location: Mount Vision, NY
I recall buying a set from Fran some years ago.

_________________
Bad decisions make the best stories.
Top
 Profile  
 
ThreePipesSmokin
PostPosted: Wed Aug 27, 2014 7:08 am 
User avatar

Joined: Wed Jun 08, 2011 10:28 pm
Posts: 1560
Location: Tampa Bay Florida
Didn't someone on one of the boards find some castle nuts? They had a very thin wall but need special driver... :think:

_________________
We don't need no stinkin' Cams!
Top
 Profile  
 
ThreePipesSmokin
PostPosted: Wed Aug 27, 2014 7:28 am 
User avatar

Joined: Wed Jun 08, 2011 10:28 pm
Posts: 1560
Location: Tampa Bay Florida
McMaster-Carr is selling JIS 8x1.25 nuts in zinc plated steel or 18-8 stainless with 12mm hex, standard is 13. :wave:

_________________
We don't need no stinkin' Cams!
Top
 Profile  
 
Jim
PostPosted: Wed Aug 27, 2014 8:11 am 
User avatar

Joined: Wed Jun 08, 2011 11:34 pm
Posts: 9866
Location: North Central NC
Iron's solution is the way to go.

_________________
If it surges, that's normal, upshift.
Top
 Profile  
 
mn-mark
PostPosted: Wed Aug 27, 2014 8:12 am 

Joined: Wed Jun 15, 2011 12:14 pm
Posts: 108
Location: Central MN
http://www.scooterworks.com/ncy-exhaust-pipe-nuts--8mm--sold-in-pairs--products-309.php#.U_3Yrbd0xjo
Top
 Profile  
 
ThreePipesSmokin
PostPosted: Wed Aug 27, 2014 8:20 am 
User avatar

Joined: Wed Jun 08, 2011 10:28 pm
Posts: 1560
Location: Tampa Bay Florida
Those are nice Mark! :thumbup:

_________________
We don't need no stinkin' Cams!
Top
 Profile  
 
Mike
PostPosted: Wed Aug 27, 2014 1:09 pm 
User avatar

Joined: Fri Jun 10, 2011 12:35 pm
Posts: 206
Location: Kansas City
Gordon had the trick fasteners on his chambered green H2B. As I recall they were some sort of aircraft fastener that did require a special tool. They were slick. My last set of small diameter spigot nuts came from Fran as well.

_________________
"... don't drink the foam." Sonny B.
Top
 Profile  
 
BarryB
PostPosted: Wed Aug 27, 2014 1:28 pm 
User avatar

Joined: Wed Jun 08, 2011 10:23 pm
Posts: 3831
Location: Colorado Springs, CO. USA
+1 Iron's note about Allen Bolts - the way to go for sure. You can usually get the right ones at Ace or other box stores now... Otherwise McMaster is your friend!

_________________
This is true. Where I grew up the hills were so steep and long, when your ball rolled down the hill you just said "screw it"...
Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  Page 1 of 2
  [ 15 posts ]  Go to page 1, 2  Next

Board index » Our legendary Kawasaki Triples » General Chat

All times are UTC - 5 hours


Who is online

Users browsing this forum: No registered users

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Jump to:  
Powered by phpBB® Forum Software © phpBB Group