Kawi2strokes.com Forum
http://kawi2strokes.com/forum/

Working on this...... CR90 Replica
http://kawi2strokes.com/forum/viewtopic.php?f=16&t=9995
Page 2 of 10

Author:  scrambler73 [ Wed Feb 18, 2015 9:32 am ]
Post subject:  Re: Working on this...... CR90 Replica

nope.... keep guessing :lol:

In all fairness, it is going to be VERY difficult to see it/figure it out without ridiculous inspection of stock H2b and CR90 photos.

That said, you can see this "feature" in a couple of the photos above.

Winner gets a cookie.

Author:  Jim [ Wed Feb 18, 2015 9:33 am ]
Post subject:  Re: Working on this...... CR90 Replica

Excessive side stand lean? :lol:

Author:  JohnnyO [ Wed Feb 18, 2015 4:41 pm ]
Post subject:  Re: Working on this...... CR90 Replica

18 Inch front rim???
Tony's bike looks like it doesn't have a shifter "pedal" on the left side maybe just set up for racing or was his right hand shift ???

Author:  ThreePipesSmokin [ Wed Feb 18, 2015 5:34 pm ]
Post subject:  Re: Working on this...... CR90 Replica

JohnnyO wrote:
18 Inch front rim???
Tony's bike looks like it doesn't have a shifter "pedal" on the left side maybe just set up for racing or was his right hand shift ???

I see the shifter, it's shorter than stock and is set up for reverse pattern, you can see the linkage rod is running from top to top. ;)

Author:  kawi3cyl [ Wed Feb 18, 2015 10:40 pm ]
Post subject:  Re: Working on this...... CR90 Replica

On a related note, I thought it interesting that Denco's PN's for their 74 H2 CR kits were CR-80-1 and CR-90-1 (did CR mean Competition Race?).

http://www.3cyl.com/tripleed/dalehbe/hbe%20010.jpg

Image

And their Street Racer kits were numbered:
SR50 (S2-350)
SR60 (S3-400)
SR75 (H1-500)
SR94 (H2-750)

http://www.3cyl.com/tripleed/dalehbe/hbe%20011.jpg

Image

How about a similarly looking H1 or S-series replica, but with an SR decal in place of the CR for mildly modded bikes with just chambers, maybe larger carbs, and little or no porting?

Author:  scrambler73 [ Thu Feb 19, 2015 10:21 am ]
Post subject:  Re: Working on this...... CR90 Replica

pretty sure "CR" just stood for "Cafe Racer"

Author:  magee [ Thu Feb 19, 2015 11:06 am ]
Post subject:  Re: Working on this...... CR90 Replica

glad to see your back in the saddle :)

Author:  oxford [ Thu Feb 19, 2015 4:16 pm ]
Post subject:  Re: Working on this...... CR90 Replica

What are the exhaust tuners on the cr80 kit? Smaller diameter inserts for a little more back pressure?

Author:  III [ Thu Feb 19, 2015 4:25 pm ]
Post subject:  Re: Working on this...... CR90 Replica

scrambler73 wrote:
There is another goofy detail that I'll point out later. ONLY found on the CR90. And it's not the lack of a grabrail either.



Piece of cake Cody, I am hesitant about lettin da cat outta da bag here though......






















Image

Author:  kawi3cyl [ Thu Feb 19, 2015 5:00 pm ]
Post subject:  Re: Working on this...... CR90 Replica

oxford wrote:
What are the exhaust tuners on the cr80 kit? Smaller diameter inserts for a little more back pressure?

I believe you are correct.
Image

Page 2 of 10 All times are UTC - 5 hours
Powered by phpBB® Forum Software © phpBB Group
http://www.phpbb.com/