Kawi2strokes.com Forum

Enthusiasts from around the world dedicated to the preservation and ritual flogging of the infamous Kawasaki 2-stroke Triples
It is currently Thu Oct 31, 2024 6:27 pm

All times are UTC - 5 hours




Post new topic Reply to topic  [ 11 posts ]  Go to page 1, 2  Next
Author Message
 Post subject: H2 running issue
PostPosted: Wed Jul 11, 2018 8:49 pm 
User avatar

Joined: Tue Nov 15, 2011 8:55 pm
Posts: 168
Location: Rhode Island
Looking for advise, 72 H2, running part throttle and under 4K RPM, RH plug will load up and bike will run on 2 cylinders until I twist throttle wide open over 4-5k RPM then it pulls at it should on all cylinders. RH pipe seems to smoke more than the other 2. Bike has Lakeland ignition with original coils and ignition wires. Any and all advise welcome.

_________________
72 H2, 76 XLCH, 78 KZ1000, 99 ZRX, 04 120ci Fatboy


Top
 Profile  
 
 Post subject: Re: H2 running issue
PostPosted: Wed Jul 11, 2018 9:19 pm 
Site Admin
User avatar

Joined: Tue Jun 07, 2011 6:36 am
Posts: 2710
Location: Dandridge, TN, USA
Likely carb issue... swap carbs to confirm.

_________________
Answers are here: http://kawatriple.com/


Top
 Profile  
 
 Post subject: Re: H2 running issue
PostPosted: Thu Jul 12, 2018 1:41 am 
Site Admin
User avatar

Joined: Tue Jun 07, 2011 6:37 am
Posts: 10460
Location: Rio Rancho, New Mexico
Check your transmission oil level, you may have a trashed crank seal. And you can fry your trans also.

_________________
Twist the throttle, tilt the horizon, and have a great time. What triples are all about...........


Top
 Profile  
 
 Post subject: Re: H2 running issue
PostPosted: Thu Jul 12, 2018 10:34 am 

Joined: Thu Jun 09, 2011 1:12 am
Posts: 238
Location: Queenborough U.K
As Moo says , and also check fuel float levels on that R/H carb


Top
 Profile  
 
 Post subject: Re: H2 running issue
PostPosted: Thu Jul 12, 2018 11:55 am 
User avatar

Joined: Tue Nov 15, 2011 8:55 pm
Posts: 168
Location: Rhode Island
Thanks for replies, does anyone have link to YouTube video showin RH seal replacement? TIA

_________________
72 H2, 76 XLCH, 78 KZ1000, 99 ZRX, 04 120ci Fatboy


Top
 Profile  
 
 Post subject: Re: H2 running issue
PostPosted: Thu Jul 12, 2018 3:35 pm 
Site Admin
User avatar

Joined: Tue Jun 07, 2011 6:37 am
Posts: 10460
Location: Rio Rancho, New Mexico
I only did the left, the right is pretty much the same. If you are very careful you can remove the cover without undoing the oil lines from the pump, just unbolting the pump.

_________________
Twist the throttle, tilt the horizon, and have a great time. What triples are all about...........


Top
 Profile  
 
 Post subject: Re: H2 running issue
PostPosted: Sun Jul 29, 2018 7:30 pm 
User avatar

Joined: Tue Nov 15, 2011 8:55 pm
Posts: 168
Location: Rhode Island
Update on running issue. Changed spark plug caps to non resistor NGK, went with iridium plugs, lowered needle to center groove ( was on 2nd from bottom) reset float levels, runs much cleaner. Right hand pipe still smokes more than other 2 and trans fluid level did go down a bit during 70 mile ride, but I don't use this bike much just plan on keeping an eye on trans level for time being.
Thanks for all the advise.

_________________
72 H2, 76 XLCH, 78 KZ1000, 99 ZRX, 04 120ci Fatboy


Top
 Profile  
 
 Post subject: Re: H2 running issue
PostPosted: Mon Jul 30, 2018 2:23 am 

Joined: Tue Jul 24, 2012 6:06 pm
Posts: 1144
Location: Honolulu
Right side crank seal replacement takes a bit of work but you will be happy with the result.


Top
 Profile  
 
 Post subject: Re: H2 running issue
PostPosted: Mon Jul 30, 2018 3:12 pm 
User avatar

Joined: Wed Jun 08, 2011 11:34 pm
Posts: 9928
Location: North Central NC
Hawaii-Mike wrote:
Right side crank seal replacement takes a bit of work but you will be happy with the result.


Right, and it can be done with the crank in if you want to. Have you done a crank seal test to check all of them?

_________________
If it surges, that's normal, upshift.


Top
 Profile  
 
 Post subject: Re: H2 running issue
PostPosted: Tue Jul 31, 2018 1:19 pm 

Joined: Tue Jul 24, 2012 6:06 pm
Posts: 1144
Location: Honolulu
Here's John's video showing the left side seal replacement. Right side is more complicated because of the clutch cover, oil pump etc. Still it's an easy job, maybe 4 hours for a novice. https://www.youtube.com/watch?v=jfqhY2RF2c4


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 11 posts ]  Go to page 1, 2  Next

All times are UTC - 5 hours


Who is online

Users browsing this forum: No registered users


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Jump to:  
Powered by phpBB® Forum Software © phpBB Group